Effective insulation of the ceiling in the bath with his hands

When constructing their own steam will rise reasonable question about what to insulate ceilings in the bath and how to make it not only effectively retain the heat in the interior space, but was resistant to high temperatures?

As is known, during heating of the internal space of the bath warm air masses are beginning to rise up, where he began to form condensation on the surface of the ceiling due to the fact that its lower temperature.

If the ceiling is not warm and did not equip it with a special layer of vapor barrier, then after a short time the heat will just outside the bath, and in addition, the condensate from the inside starts to destroy all the elements of the roof and floor.

All this will lead to the fact that warm bath will drag on indefinitely, which, respectively, will result in excessive fuel consumption.

Therefore, the reliability and durability of the roof in the near future would be in doubt.

All of this suggests that insulate the ceiling in the bath should be compulsory, especially as all the necessary work can be done by hand.

In addition, the ceiling must be protected from moisture, as well as to organize a high quality vapor barrier, which is also possible to realize your own hands.

Features of work

Over the years, the ceiling inindoor baths insulated using common clay, but today, in specialized stores you can find a huge number of more advanced materials.

insulated ceiling should only proven materials that have proved their effectiveness and practicality.

Thus, quite often in use currently Bazalit, which is an effective insulator and has a good elasticity.

he produced in the form of plates of defined dimensions, which consist of special basalt fiber.

insulate the ceiling as possible and with the help of IZOSPAN, which is available in two different versions: A and B. The first option

able to protect not only the ceiling but also the walls of the bath, is routed to the external structure of the party.In turn, in IZOSPAN intended to protect the inside wall or ceiling bath.

can also use ordinary sawdust, which will be on top of it is mandatory to fill a layer of earth ground.

as insulation for the ceiling of the bath, you can use a common material like expanded clay, which is a small-sized capsule.

Their density depends on what kind of clay used the manufacturer and how the firing was carried out.

Also you can use mineral wool, which is placed firmly over the entire surface.For high-quality insulation of the ceiling inside the bath used foil roll.

She must be completely sheathe the entire surface of the ceiling, all the joints between the sheets must perform a lap.On top of foil must perform the protective lining of the ceiling inside the bath room.

begin work on warming the ceiling with his hands, both inside and outside, should be only after will be erected the walls and roof.

There are several different ways of placing a ceiling in the bath, namely grazing, podshivnoy and panel.Depending on the material chosen and that a heater, and a method of fastening.

Warming grazing the ceiling

Typically, grazing type ceiling made in the case where it has a relatively small size, and besides, there is no structure in the attic space.

Under a ceiling suitable huge number of different insulation, and all the necessary work is easily performed with his own hands in a short period of time.

Its disadvantage is that it can damage the insulating layer, if necessary, to get to the roof.The width of its flight should not be more than two and a half meters.

Before you lay a layer of insulation, vapor barrier is necessary to properly equip.

For this type of ceiling is better to use mineral wool, which is lightweight and very easy to fit into your own hands.

ceiling also can be used for grazing type as insulation and concrete block.This material is laid over the vapor barrier with a minimum thickness shall be not less than thirty centimeters.

can use sawdust, which are stacked on the floor properly and sprinkled on top of an earthen ground.

In any case, the material that was chosen as the insulation of the ceiling bath should cover with roofing material and to protect thus against various external influences.

Usually warm nastilnyj type of ceiling can be without problems with his hands, and it does not need to have professional knowledge.

Video:

Construction of suspended ceiling

most practical option for the ceiling of the bath, which allows you to build, including, and the attic is podshivnoy.

Its design suggests the device special beams, which directly and there is mounting all the constituent elements of the structure.

Thus, this type has a ceiling support frame, which increases the overall reliability and durability.For its insulation should be all the beams inside tight sheathing layer vapor barrier.

can use the staple gun and a small wooden rack to attach it.

when laying vapor barrier it is mandatory to carry out all joints lapped, bonded together with adhesive tape.

be surface or clapboard sheathing or ordinary board after this already inside vapor barrier.

As a heater can be used as a roll, and the bulk material.For these purposes, you can use sawdust or expanded clay.

The principle is similar to the principle of laying laying this material for grazing-type ceiling.

When warming by a roll of material, its tightly placed over the entire surface and make the mandatory overlap at the joints.The material should be routed among all the roof beams.

Further, after the surface of the ceiling is insulated, the heat insulation layer tightly closed special waterproof film.

Thereafter, the entire surface of the ceiling is sewn planks, which are mounted on top of the beams.

Video:

principle insulation panel ceiling

upper base panel type baths is a collection of separate panels that are attached to each other in a special way, thereby forming a solid and smooth surface.

execute it quite difficult in a constructive manner, but in addition to its attractive appearance, a ceiling and has high levels of durability and reliability.

for its thermal insulation is best to use special panels, which can be collected by hand.For their manufacture would require wooden beams and planks.

To begin wooden material cut into blanks required size.

Then on the boards with screws fasten the board in such a way as to form a sort of pocket.

Once the shields are completely assembled, they should be waterproofed on the front side.Then they are carefully secured in the desired position, after which they will need to insulate properly.

as it is possible to use, for example, sawdust or expanded clay, and you can use the web material.

only after the upper base of the bath is fully insulated and waterproofed, proceed to build the roof truss system.

Despite the fact that the process of warming the base panel has some subtleties and nuances, all the work can be done by hand.

more information about different types of ceiling insulation in the bath described in the video, which is available below.

Video:

Insulation of the ceiling near the chimney

Any Bath mandatory arrangement requires a chimney, which usually goes through the roof.

When working stove, the internal space is heated baths, respectively, the chimney is also beginning to become very hot.

In this case, warm place near the chimney with sawdust or some other material is dangerous.Insulate the chimney is best by using concrete blocks.

As we know, this building material heat conductivity is low, and therefore, if the chimney to impose these blocks probability of ignition of the roof will be minimized.

addition, the chimney can be used as sandwich pipe, which has a structure - a pipe in the pipe.She is not afraid of high temperatures and expanded clay, which can also be used as insulation for the flue.

By warming the ceiling in the bath should be approached very carefully.As the insulation is recommended to choose only quality materials, which have good fire resistance.

If all the work carried out correctly and in accordance with the technology, then visit the baths become a pleasure.