Spray for whitewash - the quality and speed are important !

Spray for whitewash - how do I choose?

Not so long ago belilis ceiling with a vacuum cleaner or ordinary rollers and brushes.it is now replaced by more productive and easy to use spray guns for paint and whitewash, called air-brush.One of the most accessible forms of this tool is a hand-gun for whitewash.Featuring a low cost, it significantly facilitates the process of painting the ceiling.This spray gun is characterized as simple principle of operation and the device.From

metal tool body extend two hoses, one of which is immersed in the solution of underlayer, and a second end located directly nebulizer.Hand pump pumps the solution into the cavity of the gun from where it is fed to the atomizer under high pressure.As a result of the application of this tool, you get a fairly smooth ceiling covering for a very short period of time.Moreover, you will be relieved of excessive pollution of the room, which is inevitable when working with brushes and rollers.

Please note that the spray gun for manual type ceiling is still not very high performance.If you have to carry out this type of finishing work punctually and in large areas, pay attention to the pneumatic or electric tool.

Today spray gun painting the ceiling becomes more simple and quick.A good helper in this matter is, and pneumatic spray gun.Whitewash feed solution is not of any container, and from a special tank.It passes through the tool under the influence of the discharge nozzle of a compressed air compressor.This action turns into a whitewash solution of very fine particles that are dispersed as a mist, and easy to fall on the surface of the ceiling.Pneumatic tool allows you to easily work with complex and large surfaces.

Subject technologies work will cover the finished ceiling is painted uniformly as possible - without streaks and stains.However, the value of this tool is quite high.

If the price of a pneumatic spray gun is too biting for you, you can pay attention to the electric gun for whitewash.Its price is more than reasonable, and the performance and quality of the finished work are not inferior to the similar characteristics of pneumatic counterpart.The operating principle of the electric tool is often called airless as high pressure which pushes the solution is not created by means of compressed air, and with the motor.

sprayer for whitewashing - preparing a tool to work

If you are wondering how to paint ceiling paint sprayer efficiently and quickly, before work pay due attention to the preparation of whitewash solution and tools.So, the solution itself must be carefully protsezhen.This will eliminate him from impurities that can clog the nozzle orifice through which is fed and whitewashing.The quality of its application directly influence the size of the hole.

The smaller, the more smooth and neat layer you get.The large opening allows you to apply a thick layer of whitewash, but it is worth considering the fact that it will cause greater material consumption.Thus, before the work is necessary to adjust the width of the nozzle opening.After setting up the instrument should determine the length of the so-called "torch" and check the quality of the spray coating solution.For this purpose, a test is carried out painting.

result should satisfy you, if the "torch" length ranges from 75-100 cm. Focusing on this value, determine at what distance from the ceiling, you'll be finishing.If this distance is too large, fluid will simply be dissipated in the air before reaching the surface of the ceiling.Otherwise, you risk getting an ugly ceiling with stains and streaks.

Ceiling Paint spray gun - mastering the technology of applying whitewash

worth noting that the spray gun painting the ceiling - not the most complex process.It is enough to observe a number of conditions to your room decorated with white trim and the ceiling in the near future.So you've picked for the work sprayer for whitewashing with lime or chalk and divorced solution - now you can safely proceed to the study of the question, as the spray gun to paint the ceiling.

First, the coating must be applied to the corners of the room.Secondly, during the application of whitewash sprayer should be kept strictly perpendicular to the surface of the ceiling.These measures will provide you with an even application of the solution.All the actions you have carried out with the same average speed as much as possible.Otherwise you run the risk of NOT, leave lots (if it misses) or cause too much of the solution (if you hesitate).Neither one nor the other option you clearly inappropriate.

Apply whitewash recommended spiral movement.Thus each successive strip solution should be applied a few superimposed on the previous one.Do not worry if at first you do not everything is perfect!Hide existing errors will help the second layer, which is applied should be only after the complete drying of the first layer.The second layer, as is retouched, should be as thin as possible.Experts do not exclude the possibility of combining the conventional spray gun and brush.So, brush the base layer can be applied, and the spray gun - the finish.