How to install new windows in a wooden house

At a time when there were only plastic windows, it was believed that they can only be installed in the apartment.But today more and more people successfully put PVC windows in their suburban homes.Modern windows are installed in a rustic wooden house, in their qualities are not different from the windows in city apartments.However, in the method of installation, there are some features which will tell and on.

installation of plastic windows in a wooden house makes it possible to heat the house less often because the reduced heat loss.Today these designs perform well not only practical but also decorative tasks.Custom windows can make almost any color and style.For example, you can run windows, which look similar to natural wood for home from a bar.

Selection window design

By choosing windows for country house should be approached very seriously.many factors must be considered in the process.In particular, it is necessary to take account of their safety and economic construction.

First of all, touch on the issue of heat savings.It has long been known that in a window occurs before 70% of heat losses.Therefore, the main advantage, and at the same time, net of wood is that it is a "living material".Because of this, its dimensional stability decreases.That is, glass windows, like most natural materials react to moisture and sunlight.These factors lead to their deformation, due to which there are gaps, and hence falls into the house cold drafts.Therefore it requires more heating costs.Such drawbacks do not have plastic windows, which are much better conserve heat.Therefore, the choice should pay attention to glazed low-emissivity glass, which is considered to be very energy efficient.

In addition, plastic windows in an old wooden house must comply with the basic safety requirements.Modern design enable the use of special accessories, resistance to cracking, so you can not install bars on the plastic window in a wooden house.Photo examples of anti-burglary fittings are presented below.

Modern windows are thick enough to face the wall and reinforced with a closed loop, which gives them a good strength and stability.In conjunction with spetssteklopaketami similar designs obtained very reliable in terms of security.Today we can make them almost any shape, texture and color.The profile can have very different configuration.Gaskets and profiles themselves are colored not only in classic color, but also absolutely any shades.

Windows are products where deficiencies may occur only after a long time, after will be installed.They often lose their luster or fade, can become loose flaps of joint bleeds and gets into the house condensate.To avoid selection of low-quality windows are not worth saving on buying them.As a rule, more expensive construction are the highest quality.In the selection window, be aware that the basis of their strength is the durability of window plastic, sealing and stability of the construction.

When selected plastic windows, it is advisable to pay attention to the purchase of hardware.Qualitative usually lasts longer.In addition, it is necessary to carefully study the installation process step by step.The fact that the future breakages may occur because of improper installation.To the installation of plastic windows in a wooden house to avoid skewing, it is important to follow some simple rules.For home owners, made of solid wood, should be aware that this building after the construction for several years shrinks.It based the reason that before the installation of window designs a recommendation is to wait for some time.

How to put plastic window in a wooden house

Before you put new windows, you want to remove the old and well prepare the site for the installation of new ones.To the frame, on which are mounted glazing must meet the requirements for strength.If they were not so long established and are not damaged, they typically meet these requirements.Therefore, new plastic windows can be placed on them.But measurements do still have.

If the condition of the old window frame is still good, then they can still be useful.For example, in the construction of greenhouses.Therefore, in order not to damage the wooden frames, delete them to be careful.In this case it is recommended to remove the pre-window.If the frames are strong enough, the glass can not be removed.When they are removed, you need to clean and dry cloth to wipe the window box and remove the waste and debris that have accumulated in the process of dismantling.

Initially, determine the order of installation of the sill:

1. It is important to install it in the first place, because it is the basis for the subsequent installation of glass plastic windows in a wooden house.
2. horizontally along the longitudinal and transverse plane is advisable to check on the construction level.To firmly establish the window sill, it is necessary to perform notching depth up to 8 mm on each side of the horizontal window box.
3. When installing the sill should be sure to adjust its evenness.This typically use plastic plate.Less commonly used plates treated with antiseptic.
4. When the installation is complete the window sill, it is necessary once again to measure its evenness, but this time using a more accurate tool - building level.
5. For fastening window sill need to prepare in advance screws.When the assembly process is necessary to indent about 20 mm from the outer edge.To the screws do not damage the window sill, under their cap must put the right size washers.Places of attachment is not visible when the window will be permanently installed.

Next, consider how to insert a plastic window in a wooden house.

Preparations

initially need to reinstall the handle.If there is a protective film insulating glass, then her whole shoot is not necessary, because it serves as protection against mechanical damage that may occur during installation.Thus, the film is removed only partially, namely in the place of installation of the handle.

The handle itself is formulated as follows:

• set the handle in a horizontal position,
• fix the handle on a couple of bolts,
• translate the handle in the down position,
• tighten remaining bolts.

The next step will be the installation design marking and drilling of holes for the installation of fasteners.Crepe window is 8 wood screws (4 in each rack).Their diameter must be at least 7 mm.If the profile and the glazing will be heavy, the fastener diameter and their number should be increased.The distance between them should be within 360-440 mm.

How to install new windows in a wooden house

Now it's time to set yourself the plastic window in a wooden house:

1. Monitoring Centre must be done by measuring the distance between the edge and the surface of the window box.This should be done on both sides, and should avoid deviations.
2. Now the window can be set to a previously mounted sill.If the flatness of the sill has been carefully controlled, there is no need to check the horizontal plane of the window.
3. Now we need a bar of 10 mm in width.It will serve as a kind of support at the time of fastening plastic construction to the box with screws.Inserted into the timber in the gap between the frame and the window frame.And he must sit there tightly enough.Without it, the box may go away, but it will negatively affect the work of the main mechanisms.
4. When bars are in place and the window will be aligned, glazed fixed using screws.
5. Mounts between the box should be in the technological gap.It is easier to do, if we fix the window upwards.Fixing in this manner ensures not only reliable, but also so-called floating effect.This is necessary to ensure that fasteners were free to "walk" with the seasonal distortions bearing structures of the building.In doing so, the window will not warp.Consequently, the glass will be intact.
6. As you can see, the installation of plastic windows in a wooden house - a rather sensitive task.Installing double-glazed windows should be given all the measurements so that they do not interfere with the natural condensate drain.Therefore, before mounting between technological drain holes are installing planks.Only then they can be neatly put into place.Watch carefully to ensure that they are not pressed tightly to the posts.No space around the glass may crack when misalignment.
7. If too tight entry and lack of clearance between racks and glazed at least 5 mm, should contact the company from which you ordered the windows, with the requirement to eliminate this serious disadvantage.It is important that the necessary clearance has been tested before removing the old windows.
8. When the glazing is installed successfully, it must be secured with plastic glazing beads.This fixture is inserted into the groove of the frame profile thorn.By lightly tapping bead gradually deepened into the groove until until you hear a click.That sound will mean that the bead is securely established.
9. It is said that the clearance on all sides of the frame to the casing of the box should be about 20 mm.It is necessary to fill with foam.Also, as the margin for shrinkage home gap should be over the top of the casing to the timber box.It should be 60-90 mm.This stock dries timber in the wooden house they will not put pressure on the window.
10. Before filling the gap with foam, it is necessary to check the operation of the window.To do this, after inserting the valves open the window, and see how it behaves.Open to the half, and release.If the valve stays in place - will not open, not shaken and does not close on itself, it means that everything has been done correctly.
11. Now the space between the window frame and the need to carefully fill with foam.Moreover, it is done from the outside and the inside.After waiting until the foam has hardened well.Excess mixture will need to be cut.This can be done even by a simple knife.
12. When this is done, it can be assumed that the window is permanently mounted.It remains to establish the necessary fittings and drainage systems, as well as produce a finish trims.

external finish is most often done with wooden panels or plastic siding.With regard to the slopes and sills, it can be any other than plastic.More we can not forget to install flow.

People who live outside the city, if needed to ventilate the room, open the window completely.Therefore, the design for installation in wooden houses, often absent valves for ventilation.In addition, for country houses often choose windows with tilt mechanism.This is most likely due to the fact that the windows are fitted with a swing-out mechanism, generally have a higher cost.In addition, they are inconvenient for good ventilation of the room.

during installation is also recommended to put a mosquito net.You can even put the shutters, but this is not recommended, if in a country house you plan to live long.After all the windows themselves are fairly resistant to mechanical stress.

installation of plastic windows in a wooden house: video