Adjusting the plastic window on their own

question may arise, how to adjust the plastic window in the operation of the window.

Do not immediately cause a wizard to make repairs tilt locking mechanism.

Adjusting plastic windows with their hands - it is simple, and money will be spent minimal amount.

Eliminating drafts

windows are arranged so that they do not have air vents.For room ventilation flap must be set to a certain position.

In winter, the gap between the frame and sash may be too large, because the cold air in large quantities pass into the room.

This problem can be eliminated by adjusting the tilt-locking mechanism hinge.After watching the video, you can clearly observe the repair window.

First you need to open the window in ventilation mode, then make the top hinge clamp.With the onset of spring clamp should be returned to its former state.

Video:

happens that the air passes through the slit of the closed window.To determine the place where the draft, should bring a lighted match to the closed window.

Where the flame will fluctuate, it is necessary to carry out repairs.Those loops should be adjusted to any closer draft.

resolve this problem in two ways.

first - adjustment cams:

• they need to move in a clockwise direction;
• to rotate the cams you can use the tools: wrench, pliers;
• cam is not necessary to turn to the long distance of 1-2 mm is sufficient;
• if need be, the flap can be reduced by turning the eccentric counter-the clock.

adjustment of plastic windows by adjusting the pressure of a special mechanism - the second way to eliminate drafts.On the hinge side frame guide recommends to find a pressure plate.

It needs to be adjusted by turning the key clockwise.The tongue extends, and adjacent fold more tightly to the frame.

mode adjustment "winter-summer»

adjustment plastic window in the "winter-summer" mode is carried out without the help of the wizard, not spending money.To do this, change the position of pins, weakening or strengthening the sash clamp to the frame of the window.

For convenience, you can see the video, which shows the repair of PVC windows.

Video:

plants that manufacture plastic window design, provide the average position of the stud.

Fold presses are not very tight, but does not let air from outside into the room closed.

window switches to "Winter»

In winter time you need the maximum pressing the sash to the frame.Changing the position of the eccentric increase the load on the seal.The pivot is pulled a little on himself, moved to the right.

Distance from fittings to the roller should be minimal.The correctness of the installation can be checked by a notch on the video - it should be directed toward the seal.

It's worth noting that the windows that were installed recently, it is not recommended to transfer in the "winter" position.

Changes tilt-locking mechanism during the winter deforms the sealing material.it can not recover spring.

transition to a state of "summer»

By mid-spring set comfortable weather, PVC window should be transferred to the summer position.To this end, the pin is pulled and moved to the left.Correctly translated notching roller helps.

After moving the pins, it should look at the window handle.

Video:

After adjustment pins on the sealing material load is reduced, as a result of air flow from the street increases.

Such a position of the roller is recommended for all PVC windows: summer window opened and closed many times, the seal should not experience great stress and strain.

Troubleshooting handle plastic window

When it becomes necessary to replace the window handle on a new set limiter fix is ​​loose handle, do not need to contact a specialist.Independently carry out repairs can be very fast.

Replacement handles plastic window

not always handle change because of its failure.Little kids are on their own on their own to open the flap.For safety reasons, it is recommended to set the knob with integrated limiter.

to replace its handle is rotated in the opposite direction.Screws that are under it, unscrewed the old pen is removed and a new set.

When loosening the screws you can use a screwdriver.

handle plastic window jammed

happens that when turning the handle of the window going down her jam.Such a situation is not a malfunction.There was a lock handle to prevent breakage of the window.

Sometimes blocking occurs suddenly, but there is no need to call the master.Himself can handle repair and return it to its original position.

Photo:

Before taking any action, you need to determine which brand in accessories.It contains articles on constipation.

on fittings on which there is an inscription «AUBI», is to find a plate of metal with a spring.The plate should be pressed against the sealing material and turn the knob.

It is important to respect the vertical position of the sash.Deviation from any angle would interfere with the handle pivot, as will work the upper lock.

After placing windows in a vertical position with the handle turns easily and you can close the shutter.If

brand accessories «Roto», «GU», the other, it is recommended to find the tab of the metal, it is located below the handle.On it you need to press, whereby it established parallel to the seal.

handle turn to the desired position without effort.

If over time the window deformed as a result of temperature, the tongue can not reach to the response element.As a result, the handle will not turn.

Use a screwdriver to remove the screws need a response element to enclose any material (a piece of plastic, wood screw) between the frame and backstop.

Clutch "otvetku" to increase blocker - just turn the handle.

handle hard turning

reason for hard turning the knob can be dried grease.In any specialty store must purchase a penetrating lubricant.

On cylinder tube with an agent installed, and all the elements are lubricated fittings.After these simple operations handle will rotate easily.

Video:

Adjustment window horizontally and vertically

Deterioration of the hardware can be connected with the warp sash relative to the frame.

Adjusting plastic windows vertically, horizontally held their own.

Adjusting horizontal

window mechanisms may be difficult to operate, since subsided window height and can not be closed.Horizontally adjust the window of opportunity in the window hinges.

The upper loop is necessary to find holes where to insert a special device - Allen key.

In the open position of the sash is recommended to turn the key in the direction of travel clocks.

As a result of such actions leaf moved away from the loop, and the lower part of the falls.Grease fittings should not be dried.

Video:

just below the canopy can be adjusted When the window is closed.In this case, all actions must be carried out outside the window.Slip the flap is allowed no more than 1-2 mm.

Instructions how to make such actions, is contained in the video lessons.

Vertical adjustment

Adjust the vertical window can be mounted by adjusting the loop, which is located at the bottom.You must first open loop cap.

Allen key to perform the rotation in the direction of clockwise, if you need to raise the sash.The movement against the clock hands move lower the frame.

frame shift is allowed for no more than 2.1 mm.

Video:

Repair of plastic doors

Plastic doors are the same popularity as the PVC windows.But during the operation is necessary to repair them.The instructions provided in the video lessons to help cope with all the difficulties.

Adjust door horizontally

If the door leaf clings to the threshold or at the top of the door frame, then it's time to adjust it horizontally.

For this door is pressed against the hinge part and pulls the longest adjusting bolt.

door need to shift up to the moment until the blade is horizontal to the floor and the top of the door frame.Grease hinges should be fresh.

Video:

Adjusting the door vertically

If the entire length of the web, it clings to the floor, most likely, the door fell and it must be raised.This defect is due to improper installation or as a result of temperature influence.

We need to find a screw, which is located vertically on the lower end hardware.To raise the door, screw need a little pull.

Adjustment clamp

doors to increase the density of pressing the door on the hinge side, it is necessary to adjust the third screw hinges.

Clamp the door on the handle side in some models of the product is regulated by turning the eccentric.They are located at the top, bottom, middle.

If any are missing, the repair of doors is carried out by turning the spigot.According notch can be judged whether or not conducted turns correctly.The lubricant must be present at all the mechanisms.