Panels on the wall with his hands

beautiful mural on the wall of the apartment is able to decorate the room, making the interior of the exclusive.At the same time, fulfill its own is not difficult.Guided photo and video materials presented on our website, you can create a truly a work of art that can amaze friends and acquaintances.So, how to make a mural on the wall with their hands?

started manufacturing a panel, it is necessary to allocate enough space for the preparation of the required mixtures.Desirably, such a room temperature of about 20-25 degrees.The presence of ventilation also not be excessive.

Materials and tools

for making decorative panels will need:

• construction gypsum (plaster), the amount is calculated on the basis of the planned scope of work;
• sufficient number of tanks for solution;
• powerful drill with a mixer;
• airbrush compressor;
• set of brushes, putty knives, sandpaper;
• screwdriver, screws;
• hammer, chisels of various sizes, construction knife.

Because, while the need to use the gun, you should definitely buy goggles, dust mask, gloves.

Step by step instructions for the production of panels on the wall

Mouldmaking

1.1.Getting started, you first need to install the gypsum shaped rods that serve framed panels.They can be made using a very special shape.Alternatively, it is possible to purchase hardware store ready-made profiles of Styrofoam, which need to paste on the wall with glue or conventional gypsum putty.For greater confidence in the reliability of fasteners, all the details of additional panels are attached to the wall using screws.

1.2.The subject from which you want to make a plaster mold, need to put in a box with sand.At the same time, over the surface of the sand should be left to the part which is scheduled to make an impression.

1.3.The surface of the workpiece will need to clear, and then covered with a layer of grease, allowing in the future, to remove it from the plaster mold without damage.As greases, vaseline can be used.

1.4.To fill the forms should be made box.It can be made of wood, plywood, plastic or thick drywall.Setting the box on the basis of the workpiece and securely fixing it, you need to fill in all the inner space of a plaster solution.To cook it, the water must be taken is based, to result in a mixture of consistency like thick cream.Shape for strength, perform its reinforcement by a grid.

1.5.After pouring, it is necessary to knock on the edges slightly ducts for removing air bubbles from the solution.The outer surface is required to align a wide spatula.

1.6.After hardening plaster (this process will leave about 4-5 hours), the casing must be disassembled and removed resulting plaster mold.All the bumps in the form of excavated must be removed by stripping using sandpaper all the rough edges.If desired, you can, using a chisel or a cutter, put on a plaster mold additional ornaments, as well as to deepen the existing slots.

1.7.The form will need to cover the inside of quick-drying varnish or paint on nitroosnove to cast then well starred.

Manufacturing of products elements panels

2.1.After about 15 minutes after painting, it is necessary to grease the form for pouring the product.

2.2.In prepared and greased form should fill an plaster solution, well, "otvozdushit" it to eliminate possible voids.

2.3.The back of the next casting will need carefully to make amends with a spatula.

2.4.The finished product must be removed from the mold after the complete solidification of gypsum, depending on the room temperature (solution hardening process can take from 4 to 8 hours).

Fastening elements panels on the wall

3.1.All completed castings are fixed to the wall with adhesive for plasterboard and screws.Irregularities and places of contiguity to the wall, as well as the deepening of the screws, you need to seal the gypsum mixture or acrylic putty.

3.2.With fine sandpaper, you need to align all the roughness and irregularities.

Finish

4.1.After installing all the elements of the future panels need to start work on its final finishing.Alternatively, you can use a decorative finish - craquelure.At the same time, the surface will have a view of the old, covered with patina painting.

4.2.Before finishing, the entire surface of the panel will need to cover the primer deep penetration.Then apply the paint.All the layers of paint should be applied using a spray gun with a compressor, - the only way to ensure a flat surface without gaps and of leaked.

4.3.As a first layer on primer should be applied to white latex paint - basis.You will need to perform the color on all surfaces, including the decorative elements and framed panels.

4.4.For the next layer, you must close the masking tape and film all the protruding elements and the edges of the panel.Time for drying each coat should be about a day at about +25 ° C.

4.5.The next layer is necessary to apply the paint "gold."Since it is sold in powder form, it will need to dissolve the primer in a ratio of 1: 1.

4.6.After drying, the "gold" paint, you need to apply a coat of varnish krakelyurnogo.

4.7.After drying varnish (not earlier than 10 hours), remove the masking tape from the frame and decorative elements.

4.8.As the next layer must be applied to water-based white paint.The paint should not form streaks on the surface.To this end, it is possible to adopt ink name that appears in the video process on the site, or pick another option independently.As a result, it should get a white surface, covered with beautiful golden breaks and cracks.

4.9.Framed panels can be left in white or, if desired, to paint, for example, under a tree.

4.10.The entire surface of the panels for easy cleaning and protection from damage, it should cover the top layer of lacquer.

Video create a panel on the wall with his hands

Source: https://www.youtube.com/channel/UCWK2YMZtytPUHNerq_pr09w