Here are the steps of creating your own hands the pool in the country

Some people think that to make a swimming pool with their own hands - a task very difficult and almost insoluble.

However, oddly enough, even an inexperienced builder will be able to carry out the construction of the swimming pool with their hands in a country house or cottage in the garden, the main thing just to know all the subtleties of this process and adhere to the technology of construction work.

How to pool their own hands, you can look at the video in this article.

If you decide to learn how to make a swimming pool with their hands in a private home, you should start with the selection of a successful space for buildings.

determine a suitable place for swimming at the cottage or a private house, it is necessary to consider not only your personal wishes and preferences, but also the opinion of experts on where and how to build a swimming pool with their hands.

Experts advise to consider the following factors that may affect the normal body of water service:

• presence near the future pool of large trees, which due to lack of moisture pull their roots to the water, thereby harming the integrity of thestructures.Also, leaves and branches of the plants are regularly exposed to water and decompose, resulting in contamination of the entire device and the active growth of algae;
• distance from the bottom of the pool to the formation of ground water - also an important factor.Experts do not recommend to install a swimming pool where the water table is at a distance of 0.5 - 1 m from the surface of the earth.Also not recommended to place next to the other buildings on the site;
• Soil type also plays an important role.If in your area there are different types of soil, it is best to build a pool on clay soil as it passes a little moisture and will serve as a kind of waterproofing;
• matters for the construction and direction of the wind.Wind will bring in outdoor pool garbage, and better if it is to beat the wind to where you can catch it without any problems.In the same place should be placed, and the overflow pipe to dirt particles went into it together with excess fluid.

Selection form

Often, deciding to build on the site for swimming pool or in the bath with his handsmany choose for themselves the construction of irregular shape, as in the photo below, which looks very unusual.

However, it should be noted that such a pool to make very difficult, and to care for him there can be problems.

Photo:

Calculation and design of such a complex structure is a long and time-consuming, be sure to take into account the location of the filters and their power.

It should also be borne in mind that for these vessels have much more likely to buy reagents to keep the water clean.

Capacity simple form looks, of course, it's easier, but also problems in the care will be much less.Options see in the photo below.

The most common suburban pools round, oval or rectangular shape.

To make the construction of a new thing, you can supplement it with beautiful and original stairs or play with the radii of the oval pool.

Photo:

From what we can build a swimming pool?

to you in the area near the house or cottages appeared a large and beautiful swimming pool, you can go two ways: purchase the finished bowl basins, which now offer any mortar stores, but you can make the most of the available capacity of the material.

finished containers are convenient to install, environmentally friendly, resistant to the influence of the environment, are safe, but often their design is quite simple.

why many make a choice in favor of self-construction of the vessel.So you can not just make the pool form convenient for you, but also to decorate it to your preference.

The video shows step by step the device with your hands basin.

Video:

Build bowl swimming in several ways.Most often it is poured from concrete and more veneer tiles.

also very common pools of concrete blocks, which are often used for the construction of the container by hand.

Construction of concrete blocks is practically no different from the usual masonry, except for the fact that every third row of the grid should be strengthened reinforcement.

last few years in the construction of swimming pools are often used as polystyrene blocks.

Such blocks have low weight and very easy to install.

Construction of concrete pools

When you have decided on the form and place on a site location capacity, as well as filtration system, you can learn how to make a pool in the country with their own hands.

To begin to dig a pit desired shape.This can be done by yourself or with the help of special equipment, if it is possible to place it in the area near the house.

If the soil in the area near the house is loose, the walls should be done with a bias to the pit center, so they do not hit.

In addition, the bottom of the pit must also be made with a bias in the direction of the drainage system, so that the discharge of water in the future will take place without any problems.

Experts advise to do for additional drainage basin, which in the middle of the pit is a hole into which poured gravel, and then poured the entire bottom layer of sand 20 - 30 cm and tamped.

Next to the sand and laid a layer of gravel and tamped.In the process, laid all the necessary services for the loading and unloading of water.Excavation and drainage device in the photo below.

next step is to fill the day with concrete container, which should be used not less cement brand M400.

layer of the solution should be 5 cm, on top of his need to be reinforced with wire mesh 6 - 8 mm and a mesh 15 - 20 cm. Places joints necessarily strengthen thin wire.

Now reinforcement layer poured another 5-cm layer of concrete.To uniformly drying out concrete, its surface from time to time be wet with a little water.

When the concrete surface is completely hardened bottom, set the formwork for the construction of the vessel wall.It is made of 30 mm thick boards.

should provide all the places where the equipment will be installed, so that later do not have to drill holes in the concrete.

When the formwork is ready, the concrete surface of the basin bottom is moistened with water and pour a 15-centimeter layer of solution, which also add aluminum powder.

This solution will better adhere to the bottom surface.The first layer is inserted into the walls of concrete reinforcing mesh and continue to pour on the pool wall.

, must be at least 3 to vessel wall strengthened and hardened - 4 days, after which the casing is removed.The device bottom and walls of the pool in the photo.

When the pool wall completely dried up, and all the seams waterproofing plaster the inside of the walls.Then install all the equipment and erecting border of brick or concrete.

device pool in a private house can be seen on the video in this article.

Building pools of concrete blocks

device pool in the garden or in the country of concrete blocks is very common.Build a thicket of concrete blocks is not difficult not even the most experienced builders.

For such buildings use the most conventional units.

capacitance device, as in the case of a concrete basin, a start excavation, align its bottom surface and make the concrete container.

Next on the perimeter of the bottom begin to stack wall of concrete blocks.In every third row of blocks is laid for strength reinforcement.

If the ladder for the pool to be built, then it is mounted in one of the walls of the blocks.

Then the entire inner surface of the walls covered with waterproofing layer, installed the necessary equipment and is faced by any selected method.

Containers made of concrete blocks in the photo.

Photo:

Building pools of polystyrene

Recently often meet the capacity of the polystyrene blocks, the production of which takes place fairly quickly andeasily.The blocks may be of different sizes.

If you are building a large swimming pool, and the units can be selected larger.

to start doing the foundation or fill the bottom of the pool.

When the base container is dry and will get stronger it installed polystyrene blocks that are interconnected with special grooves.

With conventional manual hacksaw sizes Customized blocks for the dates if necessary.

The photo shows a device capacitance of the polystyrene blocks.

When the walls of the blocks are ready, in emptiness inserted rebar and pour concrete solution.

Do not forget to leave room for all elements of the system, so you do not have to drill holes for them.

When the vessel wall dry out and become stronger, you can pool your chosen method of stoning.

finishing pool

When the capacity of concrete blocks and ready, you are ready to finish the surface.Most often used for such works ceramic tiles, PVC film, and mosaic.

In rare cases, you can see the pool, lined with natural materials, such as marble.

As for color materials, it is best to choose a blue, blue or green and shades that create the effect of sea depth and freshness.

should also know that the darker the color of the container, the more it will seem.Video on facing tiled swimming pool.

Video:

If you choose for facing tile, then the installation should take into account that the coating will always be under the water pressure, which is why the wall sag over time by a few millimeters.Therefore

between tiles is necessary to leave a small gap, which is filled with the most flexible grout.

If you do not, then after some time of operation tile is covered over the entire surface microcracks.

for our buildings is better to choose a special tile made of porcelain, which is less than absorbs moisture and has a high strength.

Around the pool are usually laid in grooved anti-slip tiles.

Often container veneer ceramic or glass mosaic, which allows you to create beautiful and original designs and patterns.

Moreover, such small tiles can easily oblitsevat both smooth curved surface and in any of its corner.

The video shows how oblitsevat capacity mosaics.

Video:

In recent years, swimming pools covered with PVC film, which has high strength and waterproofing properties, and is relatively inexpensive.

served such coverage up to 7 years old, so it is best to use for indoor pools.

The film consists of four layers, resistant to sunlight and chemicals, it is easy to clean.

Colours PVC film is varied.

use such a film can be not only a thorough design, but also for a temporary pool of readily available materials - tires, barrels or other suitable containers, which can be used at home.

In this case, the temporary structure simply PVC film adhesive qualities.

Facing pool PVC film on video.

stones can pool in 1 - 5 days after the application of layers of plaster and waterproofing systems on the vessel wall.Gluing tile or mosaic need for a special adhesive that is resistant to water.

Begin lining the walls, with the help of a plumb determine the horizontal rows.Each row is checked using slats that each tile was placed on one level.

The joints between the tiles is filled cold-resistant and water-resistant grout selected color.