Build Daily

Интерьер

August 12, 2017 18:06

Making doorways of plasterboard

click fraud protection
Making doorways of plasterboard

Plasterboard sheets are an ideal material not only for leveling walls, but also to make the doorways of plasterboard.

drywall often used to simulate arches, niches, used for decorating doorways and passages in the room.

When you move the door, you can sew space gypsum board, which is less time-consuming and costly process than seal the doorway of brick.

Drywall - this is the material with which you can own hands to change design of the apartment, to decorate it according to your preferences.

Contents:

  • Arched design
  • manufacturing stage arch
    • Mounting metal profile
    • Putting arch
    • Close the former door
  • stages of closing a doorway
    • Bilateral closing
    • opening combined closing

Arched design

The most common design, are made of plasterboard - it is arch.It usually replaces the interior doors.

Make it possible with their own hands.Design arched openings varied: classical arch, ellipse, gothic and others.It depends on the interior height potolkov.Obratite note: the complex design of the arch can visually narrow space.

The picture presented design of arch structures.

Photo:

manufacturing stage arch

To create a doorway with your hands, it is necessary initially to draw.To evaluate all the pros and cons of the chosen style.

delete old door frame remains in place, where the door was located.The surface is cleaned.Take measurements of height and width of the arch, bend radius, calculations are made.

Mounting metal profile

After determining the type of the arches and made calculations, it is necessary to make the installation profile.For better to take the form of letters metal profile P.

You will also need the punch and metal shears.Self is better to exclude, since the cap will prevent tight fit drywall to the frame and make it difficult to finish.

On arc parts of the framework necessary to make cuts, as in the photo, at a distance of 50 mm from each other, so that the profile can be bent.Bending his pattern - frame ready.

The incisions in the profile

In the upper part of the opening is attached directly to the base frame, then curved rails.

Putting arch

According templates and calculations, cut out sides and the lower part of the arch of the drywall.They need to sheathe frame.

Fasten arch parts to the profile, starting with the sidewalls.Arch is extended along the entire length of the door opening.The joints must be sealed mesh-serpyanku and putty.

Once the joints are aligned, the filler should be treated the entire surface of the arch, close up chips and bumps that can occur during operation.

allow to dry, polish.After the primer has to dry processing Arch before it will finish.The construction can paste over wallpaper or paint.

Finish arched opening depends on the design of the room in which it is built.

The video shows the installation of an arch with their hands.

Video:

Close the former door

Plasterboard the material that can be used not only for decoration or alignment.They can be remarkably close doorways, unused room.This can be done by hand.

Installation of this design is quite simple.

Important!Do not forget to coordinate redevelopment project with the relevant authorities.

stages of closing a doorway

start work on sealing of unused doors with their hands, it is necessary to conduct measurements and calculate the required amount of material.

If the wall is sewn on the one hand, and on the other you expect to make a niche, draw it.

A niche in the wall

Prepare and attach the frame corners, which will sit drywall.

Bilateral closing the opening

metered, cut sheet of drywall on one side close the space in the wall and attach it to the frame ugolochnomu.The hollow part of the fill heat and sound insulation material.

Now you need to sew a doorway on the opposite side with plasterboard.Treat joints and prime with zashpaklyuyte.Wait until completely dry.

can now proceed to registration, in accordance with the chosen interior.An example can be seen in the photo above.

combined closing

completing work on sewing up the wall with one hand, start assembling parts on the other side.If the upper part of the opening is in the form of an arch, do it by analogy with the arched opening.

technology works the same.

Video:

In general, the design of the doorways quite diverse.Interior, nishevidnye, deaf, openings divide the room into zones.

Their finish can be different: it pasting wallpaper, and painting.Their installation in the apartment you will be able to make their own hands.The design of the buildings is huge.

We invite you to view photos of various arched openings.

Photo:

instagram viewer