Suspended Gate Building Technology

Classic gates with two doors made of wood or iron is gradually fading.They are replaced by modern design, more convenient to use.These gates can be attributed suspended gate that is equally relevant at both the garage door and the entrance to the site.

way to read our article about the gate of corrugated board with their own hands.

Hanging gates are arranged on the same principle as the sliding, instead of only in the rail construction suspended gate used rail, fixed to the upper beam ceilings.Perform such gates made of sheet metal or plastic.gate wing movement takes place along a wall or fence.Overhead doors can be manual or automated drive.

Features suspended gate:

• Hanging gates save space prior to entry, which is important with a small width directions;
• There is no need to regularly clean the snow from the entrance;
• Gates resistant to wind;
• to the gate device requires space along the line of their discovery;
• Upper protein, which carries rail, limits the height of the gate;
• winter must be regularly cleaned from the snow guide.

Materials, tools, purchased

Thanks to its simple design, hanging gates can be made with your own hands.This will require:

• metal square tube 40x40 mm and 20x20 mm for door frame;
• Sheets, corrugated or sandwich panels to manufacture the door leaf;
• square tube 120h120h4 mm to perform the supports and the upper beam;
• guide length is twice the width of the gate (typically 6 m);
• set fittings for suspended gates;
• automation kit for hanging the gate, if you want to automate the process of opening and closing;
• welding machine;
• Bulgarka;
• mortise lock.

Standard door width for cars usually does not exceed 3 meters.If you want to make gates wider to facilitate the construction of two-folding can be made, by sliding in different directions.Kits for suspended gates are sold ready-made, often together with a guide.They are designed for a certain weight of the gate, so before you buy it is necessary to count.If you make a double-leaf gate, you will need 2 sets.

Automation for opening and sold, depending on the required functions, its price varies greatly, and anyone will be able to choose a convenient option for themselves, or leave the gate without automatic opening, with manual transmission.

woodwork

If the gate is performed by metal framework to make of square tube 40x40 mm.Cut the pipe for maximum dimensions, and then cut off the ends of the tubes at an angle of 45 degrees.Lay on a flat surface in the form of future gate stykuya corners, bonded by spot welding.Measured diagonally - they must be equal, otherwise the gate bias.If necessary, the frame gate line the tapping of a hammer.Boil seams, so that moisture does not get inside the frame.Measure the internal dimensions, and then cut out the inner frame of the pipe 20x20 mm.Collect it is similar to the outer and the outer frame are welded to the inside, aligning along one edge.We clean from rust, scale, and coated with a primer and after drying - the paint on metal.

can use the w-shaped frame in which the panel is inserted into the groove for the gate of the sandwich panels.You can use a profile for the gate of corrugated board, but then you have to additionally reinforced with a metal frame area.

mount the door leaf and the lock

Door leaf cut on the inner frame size so that it is as closely laid on the inner tube skeleton.Secure the fabric to the frame with screws or rivets.If the gate is made of corrugated board, then choose the profile plate with wave height not exceeding 20 mm, so that it does not protrude beyond the frame.If the gate is planned to install mortise lock, you must immediately provide for its fastening.

Rama for gate

frame required for gates installed at the entrance to the site.The frame is made of 120x120 mm pipe by welding, it must be remembered that the upper bar must extend beyond the width of the gate opening them.In case of single wing - the width of the gate to one side, in the case of double-leaf - polshiriny on each side.

supporting ends of the vertical pipes concreted into the ground to a depth of at least 1.2 meters.It is necessary to use a level - the upper beam misalignment can lead to self-closing and opening the gate unlocked.If the door is mounted on the wall, you can easily fix the guide above the opening goal and extend it along the free wall.

Installation

guide and hardware The guide is fixed to the upper beam or wall using brackets so that part of its work, which will go on the roller bearings, has been turned down.The free end of the guide, equal to the width of the gate should extend beyond the opening.If the standard six-meter rail for this purpose is not enough, you need to be welded to it a piece of the desired length.The guide to using the adjustment screws on the brackets align with the level.

to the top of the gates on both sides of the frame are fixed castors - they are sometimes called trolleys.The gate is suspended, setting the stage for roller bearings inside the guide, then install plugs that are supplied.Install if you want to set automation and connect it in accordance with the scheme set out in the passport documentation.Put additional elements - lock knob.

Hanging gates are reliable and up to date, with the proper operation of their service life is not less than 15 years.Also suspended gate cantilever gate can be formed on the same principle, but with a guiding bar mounted at any height.They differ from the suspension, which does not limit the height of passage.

also encourage you to read about: Iron gate with their hands, and the gate of corrugated board with his hands