washing machines Errors Samsung: Samsung error codes ue, he1, he2, se, sud, 4e, 5e and faults

code

What does

Causeserror

What

1E

problem is the water level sensor (pressure switch)

damage occurred pressure switch or punctured tube.

supply pipe clogged.

tube disconnected.

Something to pinch the tube.

Relay oxidized or worn.

faulty control module.

Inspect sensor, evaluating, did not appear on it if any mechanical damage.

Make sure that the supply tube is connected.

After removing it, check for foreign objects inside or blockage.

Inspect contacts and clean them if necessary.

When failure relays need to be replaced.

3E

defective tacho motor

jammed rotor, for example, due to contact with a foreign body.

Contact compounds (either engine or tacho) damaged or oxidized.

There was a short circuit in the motor windings or appeared open.

Rate the engine, check if the rotor is jammed, and then prozvoniv wiring.

Inspect contacts and, if necessary, follow them clean.

Also inspect and clean the contacts in the tacho connections.

3E1

The machine is loaded too many clothes.

Tacho faulty.

There was damage to the engine or the contacts are oxidized.

Unload from machines of the laundry, and turn the program again.

Check if tacho works.

Inspect contacts, assessing their integrity.If need be, they should be cleaned.

3E2

tachometer comes from a weak signal due to breakage or lack of contact with the relay.

tachometer Inspect contacts and see if the details are correct.

3E3

tachosensor come from false signals.

stopped coming signal from the control module due to his fault or due to problems with the contacts.

between engine parts and clearances appeared offset increased.

Explore tachosensor and his contacts, drawing attention to their integrity.

Inspect contacts of the control module and run their sweep, if needed.

Measure the gaps between the parts of the drive, and then compare them to normal.

3E4

engine is out of order.

Broke tacho.

Their connection has been lost contacts.

Rate the engine and tachometer, and then inspect and clean their contacts.

4E

water ingress problem

The inlet valve hit a foreign object, and blocked it.

not connected to the valve coil or disrupting its contacts.

hooked hot instead of cold water.

hose is not connected to the detergent dispenser.

unscrewing the hose through which the water is dialed, make sure that the valve is a foreign object stuck.

check the contacts of the inlet valves, perform cleaning if necessary.

Make sure that the machine is supplied cold water.

Inspect the hose that fits to the dispenser.Rate for damage or blockage.

4E1

messed up hoses from the hot and cold water.

During the drying cycle the machine enters the water with a temperature above + 700C.

Make sure hoses are connected according to the instructions to the machine.

4e2

select a program for washing wool and delicate wash, and the machine enters the water with a temperature above + 500C.

sure to connect hoses.

5E

drain problem

drain hose is then pinched or blocks.

clogged sewer drain.

peremerz drain hose.

has failed impeller in the pump (corrupted or locked).

faulty drain pump.

assess the situation and the condition of the drain hose.If necessary, remove the obstruction and foreign small objects.

Check whether the outflow of water is broken into drains.

Assess the drain pump - if it works and in what condition his contacts.

8E

problem in the motor

tachosensor defective, causing the motor rotates correctly.

Contacts motor damaged or oxidized.

fault in the control circuit.

Evaluate whether tachosensor operational.

Inspect and clean the motor contacts.

9E1, 9E2

problem in power supply

Problems in the electrical circuit.

defective control module.

Identify with a multimeter electrical parameters and the voltage in the machine during the water heating and drying cycle.

When using an extension cord, make sure it is working properly.

Uc

mains voltage exceeds 276V or 176V decreased less.

job machine will resume as soon as the voltage is stable and within the limits of 176-276V.

AE

communication problem

disrupt communication between the indicator and the control module.

Check all connections, connections and contacts between the control and indicator module.

If any unit is damaged, perform the replacement.

bE1

The problem with shutting down

button switches off the machine, clamped longer than 12 seconds as a result of plastic deformation on the control panel or too strong clamping bar screws.

Check the status of the control panel.

Slightly loosen the screws too twisted.

bE2

control buttons (except the charge of inclusion) clamped longer than 30 seconds for the same reasons as in bE1 error.

Look at the control panel and the screws that it is clamped.

bE3

Short circuit relay.

Problems connecting relay contacts due to deformation or lack of connections.

Inspect the relays and contacts.

CE

cooling problem

water inside the machine is heated above + 550C, which is why it can not be merged.

faulty or malfunctioning sensor.

After cooling, the water will drain it and the bug is fixed automatically.

Evaluate whether the sensor is connected correctly and how it works.

dE

unit door problem

curved door hook, causing the switch contacts are broken.

Luc deformed due to high temperatures.

Indoor tried to open the door by force.

Check the condition of the door and its switch.

Do not try to break down the door when it is blocked.

dE1

There was damage to the lock or its connector is not properly connected.

damage the electrical insulation or faulty control unit.

sure whether he or wire that goes to him properly connected locking connector is not damaged.

dE2

spontaneously triggered door lock.

Determine whether there is a problem with excessive vibration machine.

FE

ventilation problem

fan is out of order (damage the wiring), or locks.

defective capacitor in charge of launching cooling.

Rotate the fan blades by hand, so check to see if they are blocked.

lubricate or replace the fan blades as needed.

Check wiring responsible for the operation of the fan.

Change faulty capacitor.

EE

overheating problem (in models with drying)

Broke drying heater.

Faulty sensor drying temperature.

check the status of PETN drying and temperature sensor, replace any if necessary.

HE and HE1

problem PETN

Open PETN.

Short PETN.

Broken temperature sensor.

In the tank there is no water.

temperature of the water in the tank is too high.

Check contacts PETN and temperature sensor performance.

HE2

faulty temperature sensor drying.

Lightly press down on the button in the center to the machine continued to work.If this action does not work, install a new temperature sensor.

HE3

has failed function steam

error does not occur in modern machines with a drum

LE

Water leakage

arosetank damage.

disconnected the air hose.

damage the sensor, indicating that the leak.

heater came out of the mounts.

water flows out to the high foaming caused by using an excess of powder.

incorrectly connected the hose to the detergent dispenser.

incorrectly installed drain pump or drain hose.

damaged sealing washer.

Specify whether intact tank at the connection to the transit bolts.

Make sure the drain pump well spun.

See if heater in place.

Check if the hose is connected to precisely the detergent dispenser and air hose, and if excess powder is poured.

Ensure integrity of gaskets and drain hose.

tE1

problem in the sensor temperature

Temperature sensor is faulty.

water in the machine overheating.

heater is out of order or damaged his contacts.

evaluate the work of the temperature sensor and the heating element.

Look at the pins, and then make sure that they are connected, and clean if necessary.

tE2

Broken temperature sensor or a contact violated.

should first check the contacts, and then the performance of the sensor itself.

tE3

Faulty temperature sensor condensate flow provided by a short circuit or breakage.

Check whether the sensor operates.

OE

Overflow

faulty water level sensor or has clogged hose.

valve that is responsible for the water supply can not be shut down, resulting in a constant flow of water.

Inspect the pressure switch tube and, if necessary, to eliminate its blockage.

follow its replacement When the sensor fault.

Make sure that the water supply valve is not foreign objects.

UE

balance problem

uploaded the laundry got off to one side.

balancing machine was broken.

Unload the laundry, disassemble brought down part of the return and the laundry in the drum, distributing it evenly.

Eliminate the cause of violations of balancing machines.

Sud

excess foam

Too much powder.

The machine filled powder, which is used for washing hands.

No action is required because the machine after removing the foam will continue its normal operation.

Watch what the powder is filled into the machine.