Errors washing machine Electrolux, Zanussi, AEG: error code e01, e10, e20, e50, e90 and failure washing machines Zanussi, Electrolux , AEG

code

Designation

most likely reasons (that check)

E11

problem with water intake

Crane closed.

Do not operate the Gulf of valves or damaged their electrical circuits connecting valves elektrokontrollerom.

filler system is clogged.

water pressure is too low for tank filling in the allotted time.

have drain hose wrong position.

damage the pressure switch.

disrupt elektrokontrollera.

E13

There was a leak

Water filled the machine sump.

prejudice to the provisions of the drain hose.

damage the pressure switch.

E21

problem with diverting water from the machine

Clogged drain pump filter inside.

Having problems with the drain hose (detachment, obstruction, inflection).

drain pump is broken.

damage the pressure switch.

disrupt elektrokontrollera.

E23

problem with the work of the drain pump

Blown triac responsible for the operation of the pump.

disrupt elektrokontrollera.

E24

emerged damage triac circuits responsible for the operation of the pump.

damage the circuit board.

E31

problem with

pressure sensor is faulty Either the sensor itself, or there was a break in the associated wiring.

E32

Incorrect calibration or failure of the pressure sensor.

Blockage of the drainage system, or failure of its parts.

E33

problem with level sensors

sensor does not work the first level.

problem with the wiring or the main board.

stop functioning heater protection sensor, which prevents the electric heater is turned on without water.

Water entering the housing of the heater.

Unsuitable parameters of the electrical network.

E34

problem with the performance pressure switch and level sensor to prevent boiling 2

has worn pressure switch or its wiring.

not functioning baseboard.

E35

Excess water level inside the tank (overflow)

has worn pressure switch or solenoid valve.

There was a problem with the wiring or circuit board.

E36

problem with the security sensor PETN

sensor breakage.

E37

problem with a sensor of the first level

sensor breakage.

E38

problem with pressure switch

sensor tube is clogged, so it is impossible to fix the pressure difference.

E39

problem with overflow sensor

sensor breakage.

E3A

problem with the heater relay

disrupt the electronic unit.

E41

problem with the door

Door not closed or closed tightly enough.

E42

destroy the device, locking the door.

E43

Blown triac, who oversaw the work of blocking the door device.

E44

not functioning sensor closing the door.

E45

There was damage to the electrical circuit of the triac which controls the door lock.

E51

problem with elektrokontrollerom

The triac which controls the drive motor, a short-circuit.

E52

problem with tachometer

Tachometer drive motor gives no signal to elektrokontroller due to breakage tachometer or shift of its locking washers.

E53

problem with the management of the drive motor

emerged damage triac circuits controlling operation of the drive motor.

E54

problem with the drive motor

«zalipla" reverse relay contacts.

E55

There was a break in the motor circuits.

E56

problem with tachometer

item is defective, so the signal is not filed within fifteen minutes.

E57

There exceeding the limit value consumed by the inverter current (over 15A)

not the engine is running, or there were problems with electrical wiring.

disrupt the electronic unit.

E58

Exceeding threshold consumed by inverter phase current (more than 4,5 A.)

not the engine is running, or there were problems with electrical wiring.

disrupt the electronic unit.

E59

problem with the tachometer (no signal for three seconds after turning on)

not the engine is running or the tachometer.

There were problems with electrical wiring.

disrupt the electronic unit.

E5a

heatsink overheat (temperatures above + 880S)

Unsuitable working conditions of the machine.

disrupt the electronic unit.

E5V

input voltage threshold options below (less than 175B)

damaged wiring or the electronic unit.

E5S

parameters input voltage above the threshold (more than 430B)

disrupt the electronic unit.

E5D and E5E

problem with data transfer from the inverter to the

main board appeared damaged wiring connecting the inverter board.

disrupt the electronic unit.

E5F

control unit works problem

There was a problem with the wiring or the control box.

E61

water heats slower than normal

heater damage or temperature sensor, as well as their wiring or elektrokontrollera.

E62

water is heated too quickly - the temperature is above + 880S for five minutes

damage heating element or a temperature sensor, as well as their wiring or elektrokontrollera.

E66

problem with relays PETN

relay has failed.

damage the relay control circuit.

E68

problem with the heater (leakage current exceeds the permitted parameters)

PETN damage or interference in its wiring.

E69

problem with the heater

damaged heater itself or its wiring.

E71

problem with the temperature sensor

In the sensor, or it appeared circuits shorted.

faulty heater.

in the sensor and its wiring breakage occurred.

E 74

sensor in the tank is wrong.

Faults in the wiring or circuit board.

E82 and E83

problem with selector

damaged selector or its wiring.

information wrong configuration.

problems with electronics.

E84

problem with recirculation pump

An error identification.

E85

pump is out of order.

faulty thyristor.

E92

communication problem display board and main board

used improper control board (it does not match the model).

E93

problem with setting machine

device settings wrong or out of order a printed circuit board.

E94

Settings washing invalid or has ceased to function the circuit board.

E95

microprocessor communication problem and the volatile memory

ceases to function the circuit board.

E96

problem with elektrokontrollerom

configuration controller and elements connected to it is wrong.

E97

problem with selector

Location selector does not meet the program settings.

E98

Inverter communication problem with the main board

board is incompatible with the inverter.

E99

problem with the audio unit

Incorrect connection of the inputs / outputs with audio unit.

E9A

problem with elektrokontrollerom

failed software, responsible for the connection with the dynamics of the electronics.

EA1

problem with the system of DSP, responsible for the positioning of the drum

system is out of order or broken wiring it.

EA2

An error identification.

EA3

pulley drive motor is not fixed.

EA4

system is out of order or broken wiring it.

EA5

blown thyristor.

EA6

not receive a signal to start rotation of the drum.

EB1 and EN1

problem with the mains

invalid frequency in the mains.

EB2 and EN2

exceeded the voltage in the mains.

EB3 and EN3

not enough high voltage power line.

EVE and Jeno

problem with the protective circuit

out of order relay.

EVF and ENF

An error identification.

EC1

problem with the inlet valve

lock An intake valve or wiring is damaged it.

EC2

problem with the transparency of the water sensor

has worn the turbidity sensor.

EF1

problem with drain

dirty filter in the drain hose.

Do not operate the drain pump.

EF2

detergent added to excess dosage.

drain hose is impassable due to clogging.

defective drain pump.

EF3

fired AquaControl system.

appeared damaged cable drain pump.

There was a water leak.

EF4

problem with water filling machine

Tap closed or water pressure is too weak.

EF5

imbalance linen

Things huddled inside the drum.