Clay Glass - select and use correctly

little about Glass gluing - What is special?

process of joining parts made of glass or a combination of glass and other materials is quite complicated.It is necessary to provide quality pre-treatment of joints, secure fit parts, their exact installation.Depending on the type of adhesive used, it takes full effect on all external docking location.

Glass Bonding is carried out in various technological processes.For a long time, such operations are used during assembly of cars, many household appliances, electronics manufacturing technology.The connection quality at the same time, of course, depends on the correct choice of adhesive, but not least, and perhaps greater extent - from preparation surfaces to the mix.

When selecting the operating conditions are taken into account the place of the adhesive joint supplied with mechanical, chemical and other impacts.For example, the already mentioned insertion technology windscreen, there is used adhesive sealant for glass.

increasing productivity by reducing the time of surgery, pasting allows qualitatively improve many parameters of the future of the car body.Here and increased tightness of connections, and improved aerodynamics by accurately matching the junction, and even increasing body stiffness as a whole.

How to clean the glass before bonding?

Operation insert windshield or rear window can be performed simply and in a home workshop.Of course, it requires care, but due to the fact that there is a glue for glass bonding and other desired components in the trading network can be performed independently.

very important to pretreat When docking panes.This primarily refers to the interface degreasing.Removal of pollutants, having in its composition of different oil, you need to make even for the most modern adhesive formulations, which manufacturers say about the possibility of fixing a simple application.

Most likely, this is just a publicity stunt, which increases the attractiveness of the product.In fact, every kind of pollution reduction greatly increases the bond strength and contributes to long-term operation.On which adhesive will be used depends than degreased glass.

This can apply alcohol, gasoline, kerosene, and their solutions.Perhaps the most universal degreasing agent can be called an ordinary acetone.But may use various alkaline and acidic solutions.In any case, conducting bonding glass, you need to remember about these high-risk operations and observe the safety precautions and work in an open space or a practical exhaust ventilation.

In addition, when working with glass is already used connections, before degreasing, requires careful removal of residues, which gives the old adhesive for bonding glass.After extended use, the remnants may contain small particles of dust, allergens, harmful to the respiratory system and can cause inflammatory response.

How to properly hold the gluing of glass?

Developments for bonding automotive glass, it is necessary to comply with the above requirements and workflow.So, should first carry out a set of actions for the careful recovery of the old glass.Why neatly cut seam old (suitable vibronozh, faceted string or scalpel).It is very important to remember about the possibility of cracking and fracture of materials (use gloves and goggles).

After separating the old glass to make it easier to remove, you can use suction cups.For extra safety, this work is best done together with an assistant.Then remove the perimeter of the old adhesive layer.It is advisable not to damage the metal color of the body.

if necessary, after removing the old joint and degreasing the injury site, the site is carried out staining.If this is not done, the metal will corrode. After drying the abutment degreased with special solution.

In place of the junction is applied to the adhesive, prepared according to the manufacturer's instructions, do not forget about the gum windshield.If necessary, it is better to change.Most of these adhesives have ten minutes to form a surface film, complicating a quality connection.Therefore, after application of the composition evenly (recommended thickness - 1 cm) is necessary to ascertain the glass.

This is another argument for bringing an assistant.Installed glass is required to reliably fixed with adhesive tape, capable of supporting its weight.Final hardening composition can last up to 20 hours.At this time the car is better to put the parking garage at a temperature not lower than 15 ° C.Driving and distortions of the body are not desirable.

Working with glass house is not much different in principle from the above, only the glass is inserted in the body of the car is not.Do not forget about the precautions which will save material from falling skew seam, etc..